MAXTECH CORPORATION XPVS288R9 (SF-1128HV/R9) Card Type Modem, Fax Chip Set Unidentified I/O Options Line in, line out, microphone in, speaker out Maximum Modem Rate 28.8Kbps Maximum Fax Rate 14.4Kbps Data Modulation Protocol Bell 103/212A ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis, V.34 Fax Modulation Protocol ITU-T V.17, V.27ter, V.29 Error Correction/Compression MNP5, V.42, V.42bis Fax Class Class I & II Data Bus 16-bit ISA Card Size Half-length, full-height card [Image] CONNECTIONS Function Label Function Label Line out CN1 Microphone in CN3 Line in CN2 Speaker out CN4 USER CONFIGURABLE SETTINGS Setting Label Position Microphone set for dynamic JP2 Pins 1 & 2 closed Microphone set for condenser JP2 Pins 2 & 3 closed Speaker set for stereo JP4 Closed Speaker set for mono JP4 Open Plug and Play enabled PNP1 Closed Plug and Play disabled PNP1 Open SERIAL PORT ADDRESS Setting PNP1 SW1/1 SW1/2 COM1 (3F8h) Open On On COM2 (2F8h) Open Off On COM3 (3E8h) Open On Off COM4 (2E8h) Open Off Off í PnP Closed Off Off IRQ SETTINGS Setting PNP1 SW1/3 SW1/4 SW1/5 SW1/6 2/9 Open On Off Off Off 3 Open Off On Off Off 4 Open Off Off On Off 5 Open Off Off Off On í PnP Closed Off Off Off Off SUPPORTED COMMAND SET Basic AT Commands AT, ‘+++’, A/ A, E, H, M, O, P, T, V, X, Y, Z &C, &G, &L, &T, &V, &W, &Y, &Z Extended AT Commands \A, \B, \C, \E, \G, \J, \K, \O, \Q, \U, \X, \Y, \Z %A S Registers S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18, S21, S22, S23, S25, S26, S27 Special Commands #BDR, #CLS, #MDL?, #MFR?, #REV?, #SPK=a,b,c, #VBQ?, #VBS, #VBT, #VCI?, #VLS, #VRA, #VRN, #VRX, #VSD, #VSK, #VSP, #VSR, #VSS, #VTD, #VTS, #VTX Note: See MHI Help File for full command documentation. Proprietary AT Command Set COMMUNICATIONS MODE Type: Configuration Format: AT [cmds] &Mn [cmds] Description: Selects communications mode Command Mode &M0 Asynchronous mode COMMUNICATION PROTOCOLS Type: Configuration Format: AT [cmds] Bn [cmds] Description: Selects the communication protocol for data calls Note: The B command allows the simultaneous selection of more than one suffix, enabling multiple protocols. Command Protocol B0 Enables CCITT mode B1 Enables Bell mode B2 Enables Autoscan mode B3 Enables CCITT V.23 mode only B4 Enables 300 bps connection only B5 Enables 1200 bps connection only B6 Enables 2400 bps connection only B7 Enables 4800 bps connection only B8 Enables 9600 bps connection only B9 Enables 14400 bps connection only B10 Enables 16800 bps connection only B11 Enables 19200 bps connection only B12 Enables 21600 bps connection only B13 Enables 24000 bps connection only B14 Enables 26400 bps connection only B15 Enables 28800 bps connection only DATA TERMINAL READY (DTR) Type: Configuration Format: AT [cmds] &Dn [cmds] Description: Selects modem response to DTR Command Function Command 0 Modem does not respond to DTR Command 1 Modem goes to command mode after DTR goes is off Command 2 Modem goes to command mode and disconnects (hangs up) after DTR goes off; Auto-Answer is disabled. Command 3 Modem is initialized after DTR goes off DIAL Type: Immediate Format: AT [cmds] D<#> [cmds] Description: Dials telephone number according to any modifiers included in the string Note: Any combination of modifiers can be used to produce the desired dial functions in sequence. Command Function DP Pulse dialing enabled DR Answer mode enabled; originate mode disabled following handshake initiation. DT Tone dialing enabled/Pulse dialing disabled DW Dialing resumed following dial tone detection D, Dialing paused for amount of time specified in S8 register D! Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook. D@ Wait for Quite Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string. D; Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command. DATA SET READY (DSR) Type: Configuration Format: AT [cmds] &Sn [cmds] Description: Selects DSR options Command Function &S0 DSR forced high &S1 DSR high only while modem is handshaking or connected FACTORY DEFAULT Type: Configuration Format: AT [cmds] &Fn [cmds] Description: Recalls factory default configuration and/or with software flow control enabled Command Function í &F0 Recalls factory default configuration &F1 Recalls factory default configuration with software flow control enabled &F2 Recalls factory default configuration with hardware flow control enabled &F3 Recalls factory default configuration with software flow control enabled and ignores the DTR signal &F4 Recalls factory default configuration with hardware flow control enabled and ignores the DTR signal &F5 Set modem to Direct mode FALL FORWARD/FALL BACK Type: Configuration Format: AT [cmds] &En [cmds] Description: Enables/Disables fall forward/fall back Command Function í &E0 Disables automatic fall forward/fall back &E1 Enables automatic fall forward/fallback HELP Type: Configuration Format: AT [cmds] &H [cmds] Description: Displays the modem help screen ORIGINATE MODE Type: Configuration Format: AT [cmds] &On [cmds] Description: Enables/Disables originate-only mode Command Mode &O0 Originate-only mode disabled &O1 Originate-only mode enabled PULSE DIALING RATIO Type: Configuration Format: AT [cmds] &Pn [cmds] Description: Selects pulse dial make/break ratio Command Function &P0 39/61ms at 10pps (North America) &P1 33/67ms at 10pps (Europe & Hong Kong) REPORT INFORMATION Type: Immediate Format: AT [cmds] In [cmds] Description: Displays information requested and configures Plug and Play serial number Command Function I0 Reports product ID I1 Reports ROM checksum I2 Tests and reports internal memory I3 Reports V.42bis ID I4 Reports internal ID I99=n Configures Plug and Play serial number to n (n = 0-225) RESULT CODES Type: Configuration Format: AT [cmds] Qn [cmds] Description: Enables modem to send result codes to the DTE Command Function Q0 Result code sending enabled Q1 Result code sending disabled Q2 Result code sending disabled only when answer mode is enabled SPEAKER VOLUME Type: Configuration Format: AT [cmds] Ln [cmds] Description: Controls speaker volume Command Function L0 Low volume setting L1 Low volume setting L2 Medium volume setting L3 Highest volume setting Extended AT Command Set AUTO-RETRAIN - AUTO-FALLBACK/FALL-FORWARD Type: Configuration Format: AT [cmds] %En [cmds] Description: Controls auto-retrain mode and fallback/fall-forward Command Function %E0 Auto-retrain disabled í %E1 Auto-retrain enabled AUTO-DETECT SETTINGS Type: Configuration Format: AT [cmds] %Mn [cmds] Description: Controls V.34 and V.FC while in auto-detect mode Command Function í %M0 Sets V.34 and V.FC to auto-detect mode %M1 Sets only V.34 to auto-detect %M2 Sets only V.FC to auto-detect CLEAR-DOWN SIGNAL Type: Configuration Format: AT [cmds] %Dn [cmds] Description: Enables/Disables clear-down signal Command Function %D0 Clear-down signal disabled í %D1 Clear-down signal enabled COMPRESSION/CORRECTION Type: Configuration Format: AT [cmds] %Cn [cmds] Description: Selects data compression and correction Command Function %C0 Data compression and correction disabled %C1 MNP5 and V.42bis; or data compression and correction enabled CONNECT MODE Type: Configuration Format: AT [cmds] \Nn [cmds] Description: Controls the type of connection the modem will operate in Command Function \N0 Normal mode enabled \N1 Direct mode enabled \N2 MNP reliable mode enabled \N3 Auto-reliable mode or MNP auto-reliable mode enabled \N4 V.42 reliable mode enabled \N5 V.42 auto-reliable mode or MNP auto-reliable mode enabled \N6 V.42/MNP/Normal data link enabled DCE Type: Configuration Format: AT [cmds] \Vn [cmds] Description: Reports DCE speed and extended responses Command Function í \V0 Reports DCE speed without sending extended responses \V1 Reports DCE speed and send sends extended responses \V2 Reports DTE speed without sending extended responses \V3 Reports DTE speed and send sends extended responses INACTIVITY TIMER Type: Configuration Format: AT [cmds] \Tn [cmds] Default: 0 Range: 0-90 Unit: 1 minute Description: Sets the length of time that the modem does not receive information before it disconnects. LINE SIGNAL LEVEL Type: Immediate Format: AT [cmds] %Ln [cmds] Default: 11 Range: 0-15 Unit: dBm Description: Returns a value which indicates the received line signal level PASSWORD Type: Configuration Format: AT [cmds] \P=x [cmds] Description: Stores password x (x=ASCII characters 1 through 127 excluding "?" maximum 7 characters) stored into non-volatile RAM POWER-ON AUTO-CONNECT Type: Configuration Format: AT [cmds] %Pn [cmds] Description: Enables/Disables power-on auto-connect Command Function í %P0 Power-on auto-connect disabled %P1 Power-on auto-connect enabled SECURITY Type: Configuration Format: AT [cmds] %Sn [cmds] Description: Enables/Disables call-back security and checks password Command Function í %S0 Call-back security disabled %S1 Password check enabled %S2 Call-back security and password check enabled S(status) -Registers BIT-MAPPED REGISTER S28 Type: Register Format AT [cmds] S28=n [cmds] Unit: Bit-mapped Description: Configures Power-on auto-connect, security call-back, auto-retrain, and Bell/CCITT mode settings